Install openvpn server on Debian 8 “Jessie” Linux systems

Step 4: Traffic Routing

Now, we need to enable the IP forwarding on our openvpn server.

To enable IP forwarding in sysctl. Use the below command:

# echo "net.ipv4.ip_forward = 1" >> /etc/sysctl.conf

Now we need load this modification either you reboot your server “not preferred step” or run the below command to have the same effect of rebooting the server:

# sysctl -p

At this point we are ready to enable firewall rules on our openvpn server.

Step 5: Securing the Server

Securing your server against different types of attacks is one of the most important tasks systems engineer must master, we will discuss this topic in details in another article,but now will will secure our openvpn server using iptables rules.

If you did not enable iptables on your server, YOU CAN SKIP THIS STEP AND GO DIRECTLY TO THE NEXT STEP “STARTING OPENVPN”
THIS STEP IS OPTIONAL, BUT IT’S VERY IMPORTANT, let’s play with some iptables rules:
We need to add three rules to iptables. Open port 1194 with protocol upd, and add a postrouting NAT Rule run the following commands:

# iptables -A INPUT -i tun0 -j ACCEPT
# iptables -A INPUT -p udp -m state --state NEW -m udp --dport 1194 -j ACCEPT
# iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE

Next, we need to save these two rules for permanent use, to do this on Debian Linux Family we need to install a package with the name “iptables-persistent” which takes over the automatic loading of the saved iptables rules. To do this run the following command, and accept all OK by pressing ENTER key:

# apt-get -y install iptables-persistent

Now, Those two rules will load automatically each time the system reboot.

Hint: If you added any new rules, and need to load it permanent, RUN THE FOLLOWING COMMAND AFTER ADDING THE RULES, and accept all OK by pressing ENTER key:

# netfilter-persistent save

At this Point securing your Debian Linux Family “Debian 8 “jessie”/Ubuntu 14.04, and higher” is completed, Again this section is optional.
Now, we are ready to start the openvpn server.

Step 6: Starting the OpenVPN server

Now, let’s go and enable then start the openVPN service. Run the following commands:

# systemctl enable openvpn
# systemctl start openvpn

Let’s check that the service is already running, to do this we need to do three checks:

Check 1: SERVICE CHECK

This check shows to us if there are any configurations error in /etc/openvpn/server.conf configuration file, run the below command:

# systemctl status openvpn

This command output should be something like the below image

This image shows that the openvpn service is up, enabled, and running.

Check 2: NETSTAT CHECK

The above check ” service check” is not enough, we need to do another important check to make sure that the service is running, we need to run the next command:

# netstat -nlup

You will find port 1194 assigned to openvpn, as the below image

Check 3: IFCONFIG CHECK

The above two checks show that we successfully configured the openvpn service, but we need to do another check ” optional check ” to see the installed NIC interface that openvpn uses, we need to run the next check.

# ifconfig

You will find a new installed NIC interface with name “tun0” and configured to use this IP address “10.8.0.1” as the below image

At this point the server is running and well configured.

Notes:
 1. Why should I run at least two checks to check that the openvpn service is running?
 Here's the answer:
 This because that the first check is only check on the configuration file, and it succeeded with me, but when I tried to connect to the server I couldn't, so I run the other two checks, and discovered the the service is already running, and well-configured, but netstat check didn't show that the openvpn service use port 1194, also ifconfig check didn't show any installed new NIC "tun0".
 I tried to figure out what is missing, sure there is nothing missing in the openvpn configuration file, so I searched deeply for the cause of this error, and discovered the reason.

THERE IS A MISSING KERNEL MODULE I MUST INSTALL, I MUST INSTALL THIS KERNEL MODULE "tun" IT USED BY THE OS TO CREATE THE NIC INTERFACE USED BY OPENVPN, IF THIS MODULE IS MISSING THE SERVER WILL NOT COMPLAIN ABOUT ANY ISSUE IN THE CONFIGURATION. SO IN CASE OF CHECKS TWO AND THREE ARE NOT SUCCESSFUL YOU MUST GO AND CHECK ON THE EXISTENCE OF "tun kernel module" BY RUNNING THE BELOW COMMAND"

# lsmod |grep tun

This command shows the existence of this important module, if the above command didn't give any output then you are facing the same issue I faced before, then go and install this kernel module by running the following command:

# modprobe tun

Now we installed the missing module, we need to reboot our machine to test the success of the whole configuration, run the below command to reboot your system:

# reboot

When the system is up again , rerun the three check. they must give a positive outputs.

So we have successfully completed all the server-side configuration for OpenVPN. You need now to configure the clients machines to connect to the openvpn server, go and check our article for setting up a client connection to openvpn server using a different OSes “Windows, Linux, and Mac”.

Summary

In this article we have explained the installation, and configuration of the OpenVPN server, we completed our set-up in six steps, one of them is optional, but most important for a good Systems Engineer “Step 5: Securing the Server”. We also included the solution of an issue that faced us while testing the set-up of the openvpn server. Now you can safely protect you important services from being publicly accessible through the internet.

I hope this article is good enough for you.
See you in other articles.